EJ

My wife has an EJ Special Station Wagon. We are looking to replace the head lining. The plate says the trim code is 797-B2I, but I cannot find anywhere to decipher this.

The pattern is brick or block and it looks to be white, however, I have been told that it would have been light grey as only premiers used white.

Any help appreciated

Lyle & Deb Stanley

Just wondering if you can replace the 3rd speed synchro cone and energiser spring without removing the mainshaft,thinking of replacing that and input shaft.

I don't have special tools suggested in the workshop manual to remove and replace mainshaft, can you improvise with this?

Would appreciate any advice.

I suspect my pinion angle might be a bit out,get a lot of vibration and gear jump out only going uphill. Thinking of trying some wedges at the back. Where can you buy wedges suitable for old Holdens, are they pretty universal?

Adelaide built , a while ago , was a bit rough to start with ( takes time to finish ) but recently looking near to sweet , here's some pics for the person asking about this car on this web forum... Taken at the Uradla Hot Rods and custom show a couple of years ago.... Cheers....zzzz

dose anyone know the meausurements i need to mark out on the top of the gaurds for the holes i need to drill for the wind splits to fit into

For those of you in NSW & if have or are considering the Historic 60 log book scheme, here's some food for thought.
This a facebook post of a Sydney base car club.
Hi hillbillys,

ha ha ha like to see the crappy ones then.

https://www.ebay.com...

Can anyone explain the additional trim pieces attached to this NOS EJ SEDAN Rear Panel?
It is in NZ.
Thanks,
Ron

I am trying to find out if an EJ wagon with a red motor is legal to drive on red p plates in Queensland. All the searches I’ve done say “referred” or “not determined”. Does that just mean I it’s up to me to work out if it complies with the 130kw per tonne rule? And if it’s under I’m good to go? Can anyone shed some light?

HELLO GUYS ,

I HAVE GOT MYSELF A 63 EJ HOLDEN AND BY NO SUPRISE THE ENGINE IS WORN. NOW AT THIS MOMENT I CANT AFFORD TO TAKE THE ENGINE OUT AND FIX IT SO CAN ANYONE TELL ME WHAT TYPE OF MOTOR OIL AND COOLANTS I SHOULD PUT IN IT ?

WOULD CHANGING THE SPARK PLUGS HELP ?

THANK YOU

TRENT

Hello,

Im looking for an overhaul kit for a single stromberg carburettor to suit my holden ej. Ive recently had a problem with dirty/stale fuel going through and causing all sorts of dramas.
Any info would be greatly appreciated.

Thanks,
Caedon.

Anyone know if this is important (see pucture), I am thinking maybe its just a spare hole because a non standard starter motor is being used on the car, you can't get a bolt through from starter motor side anyway.Looks like it would be tricky to get one from the other side too as it is right in the corner of tunnel and hyraulic fluid lines in the way.

We have recently purchased a EJ holden, that is totally originally its been stuck in a garage since the 1980s. Anyway wanting to put the original radio back in the car. We can not seem to find anywhere the exact specs of the radio it would came out with. The car is a sedan special.. Anyone can help with specs or better still pics or wish to sell one let us know...

Thanks

Kieran

Hi, I was wondering if anyone had any information or pictures of these original EJ EH Nasco seat belts. Im looking for something I could use as a reference to help me make up a set. Thanks

I tried to list these on eBay but they wanted more information than I was prepared to give them.
I was informed that these seats will fit from EJ to HG and are originally from and EJ Premier. They are in pristine condition, hardly been used.
MAKE ME AN OFFER :-)
I am located near LARA for pick-up or will deliver Werribee - Geelong area.

Annual ej/eh Holden club show at Sandstone Point Hotel near Bribie Island. Good weather, good turnout and good times.