published by Holden Fan (not verified) on Mon, 07/05/2018 - 15:29
am after changes made to eh holden during model run thanks warren
published by rusty on Thu, 26/04/2018 - 07:46
1. I had to do a security patch today if something doesn't work give me an email.
2. Is this a Nasco Item as it has an indent for the fuel tank or,,,no.
https://www.ebay.com...
published by Holden Fan (not verified) on Wed, 25/04/2018 - 17:09
after pros/cons helper springs for rear springs of eh sedan
published by Holden Fan (not verified) on Thu, 19/04/2018 - 16:58
okay had my crash gearbox overhauled new side with internals all new nasco gears i had-sourced over 10 years snchro hub/ gears / and all the other bearings/shaft/gear clutch/ and all the other parts in holden master catalouge what would the value be charged $200.00 Also gave back parts he said would be of use in the future regards warren
published by RustyTack on Sun, 15/04/2018 - 08:54
After 4.5 years of thinking about it I'm ready to start on my EH. My first task is to rebuild the front end.
Has anyone installed the ront end rebuild kit from OLDSKOOL Auto Parts in Campbellfield?
Thanks in advance, Cheers Rusty
published by RustyTack on Sun, 15/04/2018 - 08:53
After 4.5 years of thinking about it I'm ready to start on my EH. My first task is to rebuild the front end.
Has anyone installed the ront end rebuild kit from OLDSKOOL Auto Parts in Campbellfield?
Thanks in advance, Cheers Rusty
published by fx48_eh64 on Thu, 12/04/2018 - 17:14
Does anyone know the height difference between EH HR and LC torana seat runners?
Ihave Torana ones but seats sit to high i believe HR also sits to high in an EH, so probably need Eh ones ?
published by Holden Fan (not verified) on Thu, 12/04/2018 - 13:49
Hi Guys I'm wondering if anyone has fitted a set of new wind spliters
to their EH holden. I Have purchased a reproduction set and have been sent instruction and measurements. However I have been told that the new ones are longer because they are in fact are scaled on a EJ set not EH. The EJ, I have been told they were longer.
So in Other words I have a new set to fit on an EH with EH instruction but the wind spliter is for a EJ. Has any one encountered this problem.
published by Holden Fan (not verified) on Wed, 11/04/2018 - 13:03
PURCHASED FROM 1st OWNER AND PUT INTO STORAGE---
BEEN LOCKED AWAY IN SHED FOR 10 YEARS---
DRIVES WELL, EVERYTHING THAT SHOULD WORK WORKS--
UNREGISTERED ---
PREMIER FRONT AND PREMIER REAR SEATS WITH ARM REST -- --
HOLDEN EH SPECIAL SEDAN 186 RED MOTOR ---
5 SPEED CELICA GEAR BOX---
HR DISC BRAKE FRONT END--
COMPLETE CAR FOR RESTORATION ----
published by Old is good on Sun, 08/04/2018 - 19:43
I took the Holden for a 200km run up the highway.
It runs along fine at 110ks at 2800rpm.
After half an hour or so, if you push it up 3,000rpm it will just hit a wall. It doesn't want to rev any more. If you back off to about 80kph for a couple of kilometers it will pick up then run fine at 3,000rpm or more for another 20mins or so then lose power again.
Give it a fast run up a mountain road at high revs and it definately runs out of fuel after about 4 or 5km. Nathan just backs off to an idle for a minute or so and it's fine again.
published by Holden Fan (not verified) on Sat, 07/04/2018 - 13:39
Hi guy. Is there any problems in putting a vb commodore trimatic into a eh with 149 red motor eg flexplate, speedo
Cheers
published by 64_EH on Fri, 06/04/2018 - 14:40
Hey,
Does a red 202 thermostat housing require an O-ring, or a paper gasket only?
The old one was so degraded I can’t tell.
Thanks all.
published by Holden Fan (not verified) on Thu, 05/04/2018 - 07:25
hi all , have been given so many different opions on brake fluid. its an eh with disc brake front (hr) , i was told to use dot 4 but what im finding (as car gets driven very little ) every 18 months the seals on master cyl leaking , is this common should i got back to the old dot 3, anyone been thru this , any advice would be great
cheers
published by 64_EH on Mon, 02/04/2018 - 10:37
Hi All,
My EH has a LJ torana Diff/axle.
The previous owner fitted this Diff to accomodate larger/deep dish rims.
Will standard EH rims still fit with this LJ Diff or will there be clearance issues?
Thank!
published by Holden Fan (not verified) on Mon, 02/04/2018 - 09:57
Hi All,
My EH has a LJ Torana Diff fitted.
The previous owner did this to fit larger /deep dish rims.
Will standard EH rims still fit with this LJ diff?
Thanks!
published by Holden Fan (not verified) on Sun, 01/04/2018 - 15:28
Question, how or where do I get a spanner, to secure the 4 nuts, attaching front bumper. Have removed 2 studs, didn't reliase they actually have nuts not welded/fixed to body, so how do I reattach those bolts to the nuts now floating around inside the sub chassis?
Pages