July 27th
published by Q-ball on Wed, 27/07/2016 - 20:28
Young bloke gets his L's in about 6 months. He's now the owner of a VS ute. Not quite the Oldholden I would like.....but he's stoked. And....we get some shed time. Needs a clutch, power-steer pump kit, new springs and move the hand brake lever. Happy days
published by MarHTPREM on Wed, 27/07/2016 - 15:50
Hi all, Need some help with wheel sizes.
I want to get a set of Covo Pros. What is the biggest size I can go on the rear Without tubbing it.
I want wide on the rear with a deeper set back that the front.
I have a 9" diff which has been shortend only 10mm on each side. you help is needed. thanks guys
July 26th
published by kinswood on Tue, 26/07/2016 - 19:15
Does any one know about accelerating camshafts being offered one been told there the ducks nuts thanks
July 25th
published by mick88 on Mon, 25/07/2016 - 22:43
What is the largest diameter clutch plate/pressure plate that will bolt up to a six cylinder flywheel?
Was there a 240mm (9 1/2") available?
Thanks in advance.
Cheers, Mick.
published by Wb eighty on Mon, 25/07/2016 - 18:56
Hi guys. Any good threads around on spigot bearing installation? I've just bought a new spigot bearing from Dellow to put into the vt motor crank to suit my supra box. I noticed the old spigot on the wb turbo block crank is different. The old spigot had a wide face and lip controlling the seating depth. I'm worried now the new one will be the wrong depth if i seat it flush.
I'm wondering if i may need to buy a different bush and how to install it correctly
published by nineteenfortyeight on Mon, 25/07/2016 - 17:32
Hi All!
The Van has a new muffler fitted being supplied by Settlement Road Exhaust in Thomastown, Victoria. Only $42 freight to Blackbutt in Qld! Fitted perfectly too.
Also fitted a new pivot and plungers for the top tail gate as well as new cables for the bottom tail gate. However, I am missing the large countersunk screw on one of the cable brackets on the gate. Anyone have a spare? I haven't checked if anyone sells new ones?
The manifolds are off now to drill out the studs on the flange and replace with new ones. The faces on the exhaust manifold will be skimmed while they are off.
I will need a complete new wiring harness too. Anyone know a supplier? I've checked a few websites to no avail.
published by MarHTPREM on Mon, 25/07/2016 - 12:25
Hi Everyone,
IF there are any knowledgeable engine builders or someone that really really knows there stuff about 350chevs your HONEST HELP is needed.
July 24th
published by LockyHR on Sun, 24/07/2016 - 17:41
Engine stalled today and wouldn't start back up. Pouring fuel into it fires over but then it coughs and struggles to stay going then chokes out when accelerator is pumped. Also had problems starting in the cold so I'm thinking they are related. Visually nothing appears to be a problem and the fuel filter is new.
Should I overhaul the Carby or is there something I should look at first?
Thanks in advance
July 23rd
published by Circlotron on Sat, 23/07/2016 - 21:29
On this page http://holdenpaedia.... the way to calculate compression ration is given as cylinder volume divided by combustion chamber volume. The correct way is (cylinder + combustion chamber) divided by combustion chamber. That is to say, the largest combined volume divided by the smallest combined volume.
published by ehcrazy on Sat, 23/07/2016 - 12:40
Hi, i am trying to replace the plastic trunnion that sits between the selector leavers on the steering column. Is it possible to fit without removing the column. Thanks
published by Bundy Monaro on Sat, 23/07/2016 - 09:25
Hi guys its been awhile...:)
Chasing a good set of "no bends or buckles" front windscreen and rear window mouldings for a HD sedan.
Must be willing to post to Bundy 4670.
If you can help me out please reply.
Cheers Dave
published by LC GTR 1970 on Sat, 23/07/2016 - 08:39
Hi guys
My hz wagon is a 3 on the tree. Im about to slot a 4 speed into it and need to cut a hole in the floor for it.
Can someone please telle the dimensions and position of the hole that i need to cut.
Thanks
Jordan
July 22nd
published by kinswood on Fri, 22/07/2016 - 21:07
published by hz78gts on Fri, 22/07/2016 - 18:58
Can someone please tell me the length of a HQ sedan tail shaft with saulsbury diff the one I have is 1400mm/55 inches from center to center
TIA
Pages