You are here

Archive - Jan 24, 2016

Volvo Penta Boat Update

After a lot of filling and sanding and paint (Norglass paints are very good), upgrade to electric fuel pump, dig out 60 litres rat [Naughty Pottyword] and a few dead rats , she is a goer
https://www.dropbox....

Topic: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Celica bellhousing

Hi everyone,
Just a question. I have a dellow bell housing to suit a T50 celica box to holden 6. I was wondering if it was easy enough to re-drill holes to suit a better steel case box. Has anyone done this..?

Model: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Rat traps; )

Image: 

and white walls

  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Anyone cashed up?

  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

79 hz kingswood clutch adjustment

hey guys i have a 79 hz kingswood with 202 and 3 on the tree my clutch is coming on quite late in the pedal stroke how and where do i adjust these? can they be adjusted with gearbox on place.

cheers

Model: 
Engine: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

TonyC4195

Hi Guys.....
Anybody ever fitted a factory ram power steering unit into a HT running the standard 20:1 steering box ? They were normally fitted with a 16.9:1 but I don't have a 16:1 box and I also recall during a 16:1 factory power steering Premier and finding the steering too light.
I'm thinking a 20:1 standard box with the ram steering may be less twitchy.
Any comments or feedback would be great.
Cheers
Tony

Model: 
Engine: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Bad 308 intake gasket?

Hi guys,

After converting my 202 to a 308 and trying to get this beast to fire up and start I've noticed a few things.

When I start it it can be hard to start (Have to pump the accelerator a few times and then open the throttle to start it while cranking)

When I finally get it to idle the motor will then briefly surge and have a rough idle.

White smoke is blowing out of the exhaust manifold and a little from the rocker cover.

Oil on dipstick is slightly milky.

So I'm thinking either head gasket or intake manifold gasket.

Model: 
Topic: 
Engine: 
Section: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Holden Premier

Model: 
Topic: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.

Rims and tires for my HQ tonner question

g'day guys I am looking to put some rims and tires on my Holden HQ tonner I currently have 245/60R14 on it right now I want to go to 15x7 in the front and 15x8 in the back I would like to keep the fronts as big as possible without rubbing when I turn. The back will have the stock steel flatbed on it I just want to make the rear look nice and fat old school muscle car look. Any recommendation on wheel and tire size combos and offsets. Thanks mates and cheers

Model: 
Engine: 
  • Like0
  • no like0
  • Holdenpaedia idea0
  • Funny0
  • Wrong Category0
Please use, Holdenpaedia will get the first box on the left side. Post any suggestions.